WE ARE AN ISO 9001:2008 CERTIFIED COMPANY
Get a Quote

ASTM A516 Gr 65 Sheets & Plates

ASTM A516 Gr 65 Sheets & Plates

Carbon Steel A516 Gr 65 Plate, A516 Gr 65 Carbon Steel Sheet, Buy High Quality Carbon Steel A516 Gr 65 Perforated Sheets, Carbon Steel A516 Gr 65 Sheet, Carbon Steel A516 Grade 65 Perforated Coil Dealer, Carbon Steel A516 Gr 65 CR Sheet, Carbon Steel A516 Gr 65 Plates Exporter.

Carbon Steel Gr 65 Sheets & Plates

Table of Contents

 

Large Selection of Carbon A516 Gr 65 Hot Rolled Plates, ASME SA516 Gr 65 Carbon Cold Rolled Plates, Carbon Steel A516 Grade 65 Plates, ASTM A516 Gr 65 Carbon Steel Shim Sheet, Carbon Steel A516 Gr 65 Chequered Plate, A516 Gr 65 Carbon Steel 2B Finish Sheet, Carbon Steel A516 Gr 65 Plates Supplier in India.

Versatile Overseas is a widespread distributor of Carbon Steel ASTM A516 Grade 65 Plates, which are used to blank off the ends of piping, valves and pressure vessel openings. Available in different configuration, these Carbon Steel ASTM A516 Grade 65 Sheets are pretty much suitable to connect pipe and tubing parts.

These Carbon Steel ASME SA516 Grade 65 Coils also offer a range of advantages such asdurability, reliability and close tolerances.The main function of ASTM A516 Carbon Steel Grade 65 Sheets is to provide an access to a pipe line for metering of liquids or gases. ASTM A516 Carbon Steel Grade 65 Plates is packed together between a couple of alloys when it is being installed in a pipe line and the entire meeting is referred to as a blending. ASME SA516 Carbon Steel Grade 65 Coils are used as a substitute of the standard pipe when flow nozzle or orifice plate is being used. CS ASME SA516 Gr.65 Sheets can handle high stress from internal pressure and bolt loading since the maximum stresses are bending stresses at the center.


CS ASME SA516 Gr.70 Plates is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such as a screw or nut. Other uses of CS ASME SA516 Gr.65 Coils are as a spacer, spring (belleville washer, wave washer), wear pad, preload indicating device, locking device, and to reduce vibration (rubber washer).

Specification Of ASTM A516 Gr 65 Sheets & Plates

Gr 65 Sheets & Plates Specifications ASTM A516 / ASME SA516, BS EN 10088-2, en 10028-7, IS 6911
Gr 65 Sheets & Thickness 8 mm To 100 mm
Carbon Steel Gr 65 Sheets & Width 1500mm x 3500mm
Carbon Steel Gr 65 Sheets & Form Coils, Foils, Rolls, Plain Sheet, Shim Sheet, Perforated Sheet, Chequered Plate, Strip, Flats, Blank (Circle), Ring (Flange) etc.
Gr 65 Carbon Steel Sheets & Surface 2B, 2D, BA, NO.1, NO.4, NO.8, 8K, mirror, checkered, embossed, hair line, sand blast, Brush, etching, etc
Carbon Steel Gr 65 Sheets & Length 3000 mm to 8000 mm
Carbon Steel Gr 65 Sheets & Finish Hot rolled plate (HR), Cold rolled sheet (CR), 2B, 2D, BA NO(8), SATIN (Met with Plastic Coated)
Carbon Steel Gr 65 Sheets & Origin Indian Origin, European Origin, Japanese Origin
Carbon Steel Gr 65 Sheets & Testing and Documents Mill Test Certificates, EN 10204 3.1, Chemical Reports, Mechanical Reports, Destructive Test Report, Non Destructive Test Reports, PMI Test Reports, Visual Inspection Reports, Third Party Inspection Reports, NABL Approved Lab Reports
Carbon Steel Gr 65 Sheets & Packing Packed in Wooden Boxes, Bubble wraps, Steel Strips Bundled, or as per Customers Requests

Chemical Composition of Carbon Steel Gr 65 Sheets & Plates

Grade C Mn Si P S
Carbon Steel Gr 65 0.24-0.29 0.79 – 1.30 0.035 max 0.035 max 0.13-0.45

Mechanical Properties of Carbon Steel A516 Gr 65 Sheets & Plates

Grade Thickness Yield Tensile Elongation
Carbon Steel Gr 65 6-100mm MPa -240 min MPa – 450-585 19-23%

ASTM A516 Carbon Steel Gr 65 Chequered Plate

ASTM A516 Carbon Steel Gr 65 Shim Sheets

ASTM A516 Carbon Steel Gr 65 Perforated Sheets

ASTM A516 Carbon Steel Gr 65 Hot Rolled Plates

ASTM A516 Carbon Steel Gr 65 Cold Rolled Plates

ASTM A516 Carbon Steel Gr 65 Slitting Coil

ASTM A516 Carbon Steel Gr 65 Perforated Coil

ASTM A516 Carbon Steel Gr 65 Foils

ASTM A516 Gr 65 Sheets & Plates Thickness Chart

Thickness Thickness Size Range Surface Area per Unit weight Approx Weight per Sheet
inches mm lbs/ft² kg/m² lbs kg
0.015 0.381 36 x 96 0.630 3.07566 15.12 6.84936
0.015 0.381 36 x 120 0.630 3.07566 18.90 8.5617
0.0178 0.45212 36 x 96 0.756 3.690792 18.15 8.22195
0.0178 0.45212 36 x 120 0.756 3.690792 22.68 10.27404
0.0178 0.45212 48 x 96 0.756 3.690792 24.19 10.95807
0.0178 0.45212 48 x 120 0.756 3.690792 30.24 13.69872
0.0235 0.5969 30 x 96 1.008 4.921056 20.16 9.13248
0.0235 0.5969 30 x 120 1.008 4.921056 25.20 11.4156
0.0235 0.5969 36 x 96 1.008 4.921056 24.19 10.95807
0.0235 0.5969 36 x 120 1.008 4.921056 30.24 13.69872
0.0235 0.5969 36 x 144 1.008 4.921056 36.29 16.43937
0.0235 0.5969 48 x 96 1.008 4.921056 32.26 14.61378
0.0235 0.5969 48 x 120 1.008 4.921056 40.32 18.26496
0.0235 0.5969 48 x 144 1.008 4.921056 48.39 21.92067
0.0291 0.73914 30 x 96 1.260 6.15132 25.20 11.4156
0.0291 0.73914 30 x 120 1.260 6.15132 31.50 14.2695
0.0291 0.73914 36 x 96 1.260 6.15132 30.24 13.69872
0.0291 0.73914 36 x 120 1.260 6.15132 37.80 17.1234
0.0291 0.73914 36 x 144 1.260 6.15132 45.37 20.55261
0.0291 0.73914 48 x 96 1.260 6.15132 40.32 18.26496
0.0291 0.73914 48 x 120 1.260 6.15132 50.41 22.83573
0.0291 0.73914 48 x 144 1.260 6.15132 60.49 27.40197
0.0355 0.9017 30 x 96 1.512 7.381584 30.24 13.69872
0.0355 0.9017 30 x 120 1.512 7.381584 37.80 17.1234
0.0355 0.9017 36 x 96 1.512 7.381584 36.29 16.43937

ASTM A516 Gr 65 Sheets & Plates Sheets & Plates Weight Per Square Meter

Size (mm) Weight per
Sheet (Kg)		 Size (mm) Weight per
Sheet (Kg)
2000 x1000 x 0.7 11.5 2500 x 1250 x 1.5 38.4
2500 x1250 x 0.7 17.9 3000 x 1500 x 1.5 55.3
2000 x1000 x 0.9 14.7 2000 x 1000 x 2.0 32.7
2500 x1250 x 0.9 23.0 2500 x 1250 x 2.0 51.2
2000 x1000 x 1.0 16.4 3000 x 1500 x 2.0 73.7
2500 x1250 x 1.0 25.6 2000 x 1000 x 2.5 40.9
3000 x1500 x 1.0 36.8 2500 x 1250 x 2.5 63.9
2000 x1000 x 1.2 19.6 3000 x 1500 x 2.5 92.1
2500 x1250 x 1.2 30.7 2000 x 1000 x 3.0 49.6
3000 x1500 x 1.2 44.2 2500 x 1250 x 3.0 77.5
2000 x1000 x 1.5 24.6 3000 x 1500 x 3.0 112.0

Carbon Steel Gr 65 Sheets & Plates Other Available Products

Grade Gr 65 Hot Rolled Plates Gr 65 Carbon Steel Cold Rolled Plates
ASME SA516 Gr 65 Shims Carbon Steel Gr 65 Chequered Plate
ASTM A516 Type Gr 65 Carbon Steel Strips ASTM A516 Carbon Steel Gr 65 Foils
PED Approved ASME SA516 Gr 65 HR Plates Grade Gr 65 Shim Sheet
ASME SA516 Gr 65 2B Finish Plate AISI Gr 65 Carbon Steel Plate
Gr 65 Carbon Steel Sheets ASTM A516 4 Finish Plate
Gr 65 Carbon Steel 2D Finish Plate Carbon Steel Gr 65 Sheet No 4 Finish Size
ASTM A516 Type Gr 65 Cut To Size Sheets & Plates Gr 65 Carbon Steel Circle Price Per Kg
ASTM A516 Gr 65 Stainless Coils AISI Gr 65 Carbon Steel Foils
Gr 65 Sheet at Best Price in India ASME SA516 Gr 65 Strips
Carbon Steel Gr 65 20 mm Thick Plate Suppliers at low prices Carbon Steel ASME SA516 Gr 65 Sheets
Carbon Steel Gr 65 Outokumpu Sheet Supplier Carbon Steel Gr 65 Matte Sheet Price

CS Sheets & Plates

Sheets & Plate Materials

Product Range

manufacturer & exporter stockist supplier of Carbon Steel, mild steel and alloy steel Ferrous & Non Ferrous Products

Quick Contact